Glue Beads onto Wire Lace Ribbon

See the tabs below for all products and tools used in this technique, plus any additional tips that may be helpful to you!

Learn to use glue with the wire lace ribbon to create a necklace with "floating" beads.
Inspiration Level 
Approximate Finished Length3mpty
Printer-Friendly
Tip 13mpty
Tip 23mpty
Tip 33mpty
Tip 43mpty
Tip 53mpty
Tip 63mpty
Tip 73mpty
Tip 83mpty
Tip 93mpty
Tip 103mpty
3mpty
3mpty
3mpty
3mpty
3mpty
3mpty
3mpty
3mpty
3mpty
3mpty
3mpty
3mpty
3mpty
3mpty
3mpty
3mpty
3mpty
3mpty
3mpty
3mpty
3mpty
3mpty
3mpty
3mpty
3mpty
3mpty
3mpty
3mpty
3mpty
3mpty
3mpty
3mpty
3mpty
3mpty
3mpty
3mpty
3mpty
3mpty
3mpty
3mpty
3mpty
3mpty
3mpty
3mpty
3mpty
3mpty
3mpty
3mpty
3mpty
3mpty
3mpty
3mpty
3mpty
3mpty
3mpty
3mpty
3mpty
3mpty
3mpty
3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

Step 1

Crimp a clasp onto the wire lace ribbon.

Step 2

String a bead onto the other end of your wire lace ribbon.

Step 3

Place a drop of glue on the wire lace ribbon where you want your bead to be. I placed this drop of glue about 1.5 inches from the crimp bead.

Step 4

Slide your bead over the drop of glue. Hold it there for about 15 seconds.

Step 5

The glue will set in about 20 minutes but you can still keep adding beads!

Step 6

String another bead onto the wire lace ribbon.

Step 7

Place another drop of glue on the wire lace ribbon where you want your bead to be. I placed this drop of glue about 1 inch from the last bead.

Step 8

Slide your bead over the drop of glue. Hold it there for about 15 seconds. Continue this pattern, adding beads as close or as far away from each other as you wish until desired length.

Step 9

Finish your piece by crimping a jump ring or the other end of your clasp onto the wire lace ribbon.

     

Copyright © 2004 – 2014 Fusion Beads, Inc. FusionBeads.com®

Fusion Beads Inc, Beads, Seattle, WA