Making a Clasp - Simple Hook

See the tabs below for all products and tools used in this technique, plus any additional tips that may be helpful to you!

Make your handmade jewelry into unique innovations by crafting your own hook clasps.
Inspiration Level 
Approximate Finished Length3mpty
Printer-Friendly
Tip 13mpty
Tip 23mpty
Tip 33mpty
Tip 43mpty
Tip 53mpty
Tip 63mpty
Tip 73mpty
Tip 83mpty
Tip 93mpty
Tip 103mpty
3mpty
3mpty
3mpty
3mpty
3mpty
3mpty
3mpty
3mpty
3mpty
3mpty
3mpty
3mpty
3mpty
3mpty
3mpty
3mpty
3mpty
3mpty
3mpty
3mpty
3mpty
3mpty
3mpty
3mpty
3mpty
3mpty
3mpty
3mpty
3mpty
3mpty
3mpty
3mpty
3mpty
3mpty
3mpty
3mpty
3mpty
3mpty
3mpty
3mpty
3mpty
3mpty
3mpty
3mpty
3mpty
3mpty
3mpty
3mpty
3mpty
3mpty
3mpty
3mpty
3mpty
3mpty
3mpty
3mpty
3mpty
3mpty
3mpty
3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

3mpty

Step 1

Begin with a 3 inch piece of 18 gauge wire. Grasp the end of the wire with the round nose pliers.

Step 2

Rotate the pliers to form a complete loop. This will be a small loop - use it at the end of your piece of jewelry.

Step 3

Using the base of the round nose pliers, grasp the wire directly above the loop just made.

Step 4

Pull the wire back, down and around the pliers until the wire touches the loop.

Step 5

Use the wire cutters to cut the end of the wire off at about the point when it meets the small loop.

Step 6

Then grasp the end of the wire with the tips of the round nose pliers.

Step 7

Slightly bend the wire back. This will put a soft bend in the wire. This will finish off the hook.

Step 8

Congratulations! You have made a simple hook clasp.

Step 9

To harden the clasp without changing its shape, place the clasp on a steel bench block. Then use a nylon hammer or plastic mallet. Hammer the clasp several times.

Step 10

To flatten the clasp, place the clasp on a steel bench block. Then use the flat side of a chasing hammer or a brass hammer. Hammer the clasp several times.

Step 11

The clasp will also be hardened as well as being flattened. The loop of the clasp will open up slightly when hammered - close the loop just like you would close a jump ring.

 

Copyright © 2004 – 2014 Fusion Beads, Inc. FusionBeads.com®

Fusion Beads Inc, Beads, Seattle, WA